PGT Shingle, Tile & Metal Roofing Nationwide | TruePane Windows & Doors

PGT Shingle, Tile & Metal Roofing in Pompano Beach: What to Know First

We fix PGT shingle, tile and metal roofing systems across Pompano Beach as an independent PGT service provider. Most PGT roof repairs run between $350 and $2,800 depending on what failed, and we complete the bulk of them in one visit. If you’re a PGT owner whose roof is leaking, lifting, or showing rust at the fasteners, this page covers what actually goes wrong and what it costs to make it right. Call (863) 591-8673 and a live person answers.

Call (863) 591-8673

How PGT Products Fail - and How We Fix Them

• Shingle systems: granule loss and seal strip failure. PGT’s architectural shingle lines hold up well in dry heat but struggle with Pompano Beach’s humidity cycle. The real problem we see is the asphalt seal strip curing out prematurely when attic ventilation isn’t balanced, so shingles that looked fine at install start lifting at the corners within six or seven years. We identify the ventilation issue first, then replace only the affected shingles with color-matched stock rather than reroofing a section that doesn’t need it.
• Tile systems: underlayment rot at the eave line. PGT’s concrete and clay tile profiles shed water fine, but the underlayment underneath breaks down faster in Pompano Beach than most owners expect, especially on the east side of Federal Highway where salt spray sits on the roof. By the time a tile cracks or shifts, the underlayment beneath has often been wicking moisture for two or three years. We pull the affected tiles, patch the underlayment with a high-heat peel-and-stick membrane rated for coastal Florida, and reset the original tile rather than telling you the whole roof is shot.
• Metal roofing: fastener backout at the expansion joints. PGT’s standing seam and metal shingle panels expand and contract hard under Pompano Beach sun. The neoprene washers on the fasteners compress over time, and the screws start backing out a thread at a time. It’s a slow leak that shows up as a rust stain on the ceiling before you ever see water. We replace the fasteners with the next gauge up and add a butyl tape collar, which holds through the expansion cycle better than the OEM washer alone.
• Flashing failures at penetrations. This is the failure mode we see most across every PGT roof type in Pompano Beach: pipe boots, vent flashing, and chimney counterflashing that were never sealed to the PGT profile correctly. The symptom is a drip near a skylight or vent stack that comes and goes with wind direction. We re-cut the flashing to match the actual panel or shingle profile, not a generic template.
• Ridge cap separation on tile roofs. PGT tile ridge caps in Pompano Beach work loose because the mortar bed shrinks in the summer heat, and once one cap shifts, water gets under the whole ridge line. We reset the caps on a flexible polyurethane adhesive instead of a rigid mortar bed, which gives the assembly room to move without opening a gap.

Our PGT Shingle, Tile & Metal Roofing Process

1. 1
   You call, a person answers. We get your address, your roof type, and what you’re seeing. If you’re not sure whether the leak is roof or window, we’ll ask questions that sort it out before we ever roll a truck.
2. 2
   We inspect the roof and the attic. Dale Kessler trained to read a spec sheet before he sold anything, and that habit applies to diagnosis too. We look at the roof surface and the underside of the decking. Heat signature, fastener condition, and underlayment moisture tell us more than the visible damage does.
3. 3
   Parts decision: OEM vs. quality aftermarket. PGT’s warranty covers manufacturing defects, not installation or weathering issues, so for most Pompano Beach repairs we use OEM PGT components where the profile is still in production, and proven aftermarket flashing or fasteners where the OEM part was the weak point to begin with. We walk you through that decision on paper before we touch anything.
4. 4
   We do the work and document it. Photos before, during, and after. The fasteners we used, the membrane we set, the sealant cure time. You get that record whether you ever file a claim or not.
5. 5
   We test for the leak, not the patch. A water test at the repair site plus a look at the underside of the decking before we call it done.
6. 6
   We stand behind it. Every PGT roofing repair is covered by our Done Right Promise. If it’s not right, we make it right. No paperwork fight, no arguing.

What PGT Shingle, Tile & Metal Roofing Costs in Pompano Beach

Here are honest ranges for the PGT roof work we do most often in Pompano Beach:

• Shingle replacement (small section, including seal strip touch-up): $350-$650
• Tile reset with underlayment patch (up to 20 tiles): $800-$1,800
• Metal roof fastener replacement and re-torque (per 100 sq ft): $500-$1,200
• Flashing re-cut and re-seal at a penetration: $300-$750
• Ridge cap reset (tile roof, 20 linear feet): $700-$1,600
• Full roof inspection with written findings: $250

What moves the price is access, pitch, how much decking damage has already happened, and whether we’re matching a discontinued PGT profile. We quote a fixed price before we start, and the bill matches the quote. Call (863) 591-8673 for a free estimate on your specific roof.

Why Pompano Beach Homeowners Call TruePane Windows & Doors for PGT Work

We’re a local company that’s been rooted in Broward County since 2008, and we still answer the phone with a person, not a menu. Our technicians are background-checked and uniformed, and they know PGT products well enough to tell you when a repair makes sense and when you’re better off putting that money toward replacement. We also service CGI, CWS, ES Windows, and ECO Window Systems, so if you have a mixed brand house we can handle the whole job in one visit. Every repair carries the Done Right Promise. Both warranty layers get registered in writing before the truck leaves your driveway. If it isn’t in writing, it isn’t a warranty.

FAQs