Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Impact Garage Doors: The Pompano Beach Owner’s Guide
CGI impact garage doors in Pompano Beach typically cost $2,400 to $5,800 installed, depending on door width, panel count, and whether we’re matching an existing CGI model or retrofitting a new one. We keep the most common CGI replacement panels, struts, hinges, and roller assemblies on the truck, so a service call in Broward County usually gets the door working again in a single visit. Most owners discover the failure the hard way: a door that used to glide quietly now groans halfway up, hangs a few inches short of the ceiling, or settles unevenly on the slab after a storm. In Pompano Beach, salt air and summer humidity work on impact door hardware year-round, and the parts that fail first are almost always the ones that move.
Which CGI Models This Applies To
Most CGI impact garage doors we service in Pompano Beach fall into two series: the CGI Sentinel and the CGI Barbados line. The Sentinel is the heavier door, built to Miami-Dade and Broward wind-load standards with reinforced stiles and a thicker bottom rail. The Barbados is lighter, uses a narrower strut pattern, and is common on older Pompano Beach homes built between 1995 and 2010. The compatibility gotcha is this: CGI’s hinge and roller geometry changed between the pre-2012 and post-2012 production runs. A hinge stamped “CGI-72” will not sit flush on a 2015-era panel even though the door looks identical from the garage floor. We identify the right part by reading the label on the end stile and measuring the roller stem length, never by guessing from a photo.
On the OEM versus aftermarket question, we’re straightforward about it. For the panel sections themselves, OEM CGI is the only option we’ll recommend, since impact certification is tied to the panel’s exact extrusion. For wear items like rollers, cables, and weather seals, quality aftermarket equivalents from Clopay or Amarr distributors hold up just as well and cut the part cost by a third. We stock both and put each option on paper with a price before any work starts. We are an independent service provider and installer, not a CGI factory affiliate, which means we match pricing without a corporate markup attached.
Signs Your CGI Impact Garage Door Is Failing
- Door binds or stalls at the same height every time. This usually means a strut has loosened or a hinge bearing has worn egg-shaped, letting the panel rack slightly out of alignment. In Pompano Beach, the constant temperature swing between a hot garage and evening humidity accelerates this, especially on east-facing doors.
- Loud metal-on-metal grinding near the top of the track. The roller stems on CGI doors are galvanized, but the bearing inside the roller is often not. Once the bearing seizes, the roller flats out and grinds. Running the door this way scores the track and turns a $40 roller swap into a track replacement.
- The door sags visibly on one corner when closed. That sag is the torsion spring losing tension or a cable that has stretched unevenly. It puts uneven load on the panels and, over a season of salt air, starts pulling the bottom rail apart at the corner joint.
- Water stains or rust streaks running down the inside face of the lowest panel. The bottom weather seal on a CGI door encapsulates a steel retainer that rusts through in coastal air. Once the retainer lets go, the seal folds flat and stops sealing, and the bottom panel sits in standing water every summer afternoon.
- The door reverses mid-travel for no apparent reason. Older CGI openers paired with newer safety eyes can false-trip, but on the door side this commonly traces to a failing roller bearing or a bound hinge that spikes the motor’s draw. The opener’s force limit clamps down and the door shudders back up.
Replacement Cost & What’s Included
In Pompano Beach, a full CGI impact garage door replacement runs $2,400 to $5,800 installed. A single damaged panel replacement usually lands between $600 and $1,200, depending on the panel’s width and whether we’re matching a Sentinel or Barbados profile. Smaller wear-part jobs, like rollers, hinges, and cables, typically run $180 to $450 for parts and labor in one visit.
What drives the range is panel width, the number of struts, whether the existing tracks can be reused or are pitted beyond service, and whether the job requires rerouting the opener’s force limits. Every quote is written line by line, with the part and labor separated. We register both warranty layers, manufacturer and our workmanship, before the truck leaves the driveway. If it isn’t in writing, it isn’t a warranty.
DIY or Call Us?
One thing to know up front: the torsion spring on a CGI impact door is under enough tension to take off a finger or open a scalp. That spring is not a weekend project, and neither is the cable that wraps it. We have pulled homeowners off ladders who were about to release a winding cone with a screwdriver in the wrong slot. If the spring or cable is the problem, call a trained technician. That’s not a sales line; it’s a hospital visit avoided.
What a careful owner can check safely: the rollers for visible flat spots, the hinge screws for tightness, the weather seal for cracking, and the track for debris. You can also photograph the end-stile label so we have the exact model on the first call. What you should not do is loosen any fastener on the spring assembly or attempt to re-seat a cable that has jumped the drum. Call (863) 591-8673 and we’ll have a background-checked technician out with the right parts.
FAQs
Plan on 12 to 18 years for the door assembly in Pompano Beach’s coastal environment before major components need replacing, with roller bearings and bottom seals typically giving out in the 6 to 9 year range regardless of the panel condition. The panels themselves hold up longer, but the moving parts and fasteners fail from salt air long before the extrusion does. Call (863) 591-8673 for an honest evaluation of your door rather than an automatic replacement pitch.
Most CGI impact garage doors we see in Pompano Beach are repairable without a full replacement; we replace panels, springs, cables, rollers, struts, and seals while leaving structurally sound sections in place. Full replacement only makes sense when the bottom panel’s steel retainer has rotted through, the track is scored, or multiple panels have delaminated. We’ll show you the damage before quoting either path.
A spring or roller swap takes one visit, usually 45 to 90 minutes once the truck is in the driveway, and we stock the common CGI spring sizes and roller lengths on the truck for Pompano Beach service calls. A single panel replacement takes a few hours because the new panel has to be ordered, matched, and set true to the neighboring sections. Call (863) 591-8673 and we’ll give you a straight time estimate for your specific door.
We stock the most common CGI hinges, rollers, cables, weather seals, and spring assemblies for the Sentinel and Barbados lines that dominate Pompano Beach garages, and we order panels and odd-width struts direct with a 3 to 7 day lead time. We also stock compatible parts for PGT, CWS, and ES Windows doors, so if you have a mixed house we can often resolve it in one appointment. If we don’t have the exact part in the truck, we tell you that on the phone before we schedule, not after we arrive.
Get Your CGI Garage Door Fixed Right
If your CGI impact garage door is grinding, sagging, or leaking air at the bottom, call TruePane Windows & Doors at (863) 591-8673 for a free estimate and a straight answer. Dale Kessler grew up in the Pompano Beach Highlands and has spent two decades setting and finishing doors across Broward County, and the standard on every job is simple: if the pane is not true, the job is not done. We stand behind the work, the warranty, and the promise, in writing. A live person answers the phone, day or night.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Pompano Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.