Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterECO Window Systems Custom & Geometric Windows in Pompano Beach: What to Know First
We provide independent ECO Window Systems custom and geometric window service across Pompano Beach, from arched transoms in The Hills to oversized trapezoid units in Harbor Village. Most custom-shape repairs run $280-$640 depending on glass type, frame condition, and whether we’re matching an existing sightline or fabricating a new unit, and most jobs are done in a single visit. Call (863) 591-8673 if you own a ECO Window Systems shaped window that’s fogged, binding, or leaking. As an independent ECO Window Systems service provider, we are not affiliated with or authorized by the manufacturer, but we know their lines well enough to tell you honestly when a repair is worth it and when replacement is the only square deal. This page is for Pompano Beach homeowners with ECO Window Systems custom and geometric windows who want straight answers, not a sales pitch.
How ECO Window Systems Products Fail - and How We Fix Them
ECO Window Systems builds a solid frame. The failure points we see on custom and geometric units in Pompano Beach are almost always at the joints, the seals, and the glass edge, not in the extrusions themselves. Here are the five patterns we see most often, and what we do about each one.
- Radius and arched units losing their seal at the curve. On ECO’s radius and arch-top lines, the bent-glass section is the first place a seal lets go. The curve puts uneven stress on the spacer bar, and after a few Pompano Beach summers with 90 percent humidity, the desiccant inside the spacer saturates and you get permanent fogging between the panes. We see this more often on south and east elevations that take full afternoon sun. The fix isn’t a reseal, it’s a new insulated glass unit (IGU) cut to the same radius. We measure the arch in three places, not one, because a two-degree variance makes the IGU sit proud of the frame.
- Trapezoid and parallelogram units with corner stress fractures. Custom geometric shapes like trapezoids and parallelograms concentrate stress at the acute corners. If the original install didn’t leave proper expansion allowance, the glass binds against the frame and you get a hairline crack that runs from the corner. We’ve pulled enough of these in Pompano Beach Highlands to know the pattern. The fix is a new IGU with a tempered option if the opening is near a door or within 18 inches of the floor, which code requires. We check the frame square before we order anything, because a racked opening will crack the next lite too.
- Failed glazing beads on octagon and circle-top units. ECO’s glazing beads on shaped windows are thinner than what you see on their rectangular lines. After years of direct sun, the vinyl beads shrink and pull away at the miter joints, which lets water into the frame channel. You’ll see it first as a dark stain at the bottom corner of the shape. We replace the bead with a matching profile, not a universal trim that looks close enough, and we bed the new bead in sealant before we set it. A universal bead on a shaped window looks wrong from the curb and leaves a gap at the miter.
- Hurricane-season water intrusion at the mullion intersections. Custom geometric windows frequently get mulled to a standard unit, like a half-round over a fixed rectangle. The mullion pack between the two units is a water entry point on ECO assemblies if the original installer used a thin sealant line instead of a true mullion cover with proper drainage. In Pompano Beach, where a July storm can drive rain sideways off the ocean, that’s the difference between a dry sill and a stain running down the drywall. We open the mull joint, inspect the drain channels, replace the sealant with a marine-grade product, and re-set the mull cover. If the original mull has no drainage at all, we’ll tell you and recommend refabrication.
- Oversized openings with bowed frames from salt-driven settling. Large custom units over six feet wide, especially in older Pompano Beach ranch houses near the Intracoastal, show frame bow over time. It’s not an ECO defect so much as what salt air and sandy soil do to a house. The frame bows, the sash binds, and the operator gears strip. We re-square the frame with shims before we replace the hardware, because putting a new operator on a bowed frame means you’ll replace it again in two seasons. If the frame is too far gone, we’ll quote you an honest replacement and help you pick a line, including PGT, CGI, CWS, or ES Windows, side by side on paper.
Our ECO Window Systems Custom & Geometric Windows Process
Every ECO shaped window job in Pompano Beach follows the same steps, whether it’s a half-round transom in Garden Isles or a full-wall trapezoid bank in Cresthaven. Here’s what to expect.
- 1
Call and tell us what you’re seeing. A live person answers, 24/7. You describe the symptom; we’ll ask about the shape, the size, and whether it’s on a sunny wall. We’ll schedule a visit that fits your day.
- 2
We measure the window, twice. Our technician arrives in a uniform, background-checked, and measures every leg and radius of the opening, then measures again. On a geometric shape, a quarter-inch miss at one corner compounds across the whole unit.
- 3
We diagnose and tell you straight. We’ll point to the actual cause, not a guess. If the seal failed, you’ll see the fog and we’ll explain why it happened. If the operator is stripped, we’ll show you the worn gear. No mystery, no upsell.
- 4
We decide OEM or better, together. We source ECO-compatible parts when the warranty or the sightline demands it, and we’ll recommend quality aftermarket options when they’re equal or better and cost you less. You get the choice, on paper, before anything is ordered. We never install a part that voids a remaining ECO warranty without telling you, in writing, what that means.
- 5
We do the work in one visit. For most custom and geometric repairs, the new IGU or hardware is fabricated to spec and installed on the same trip. We re-glaze, re-seal, and re-set the unit, then clean the glass and the frame.
- 6
We test it with you and put the promise in writing. We run the window through its full travel, check the seal, and inspect the drainage. You get the Done Right Promise and The Keystone Standard: both manufacturer warranty layers registered in writing, durations stated, before our truck leaves your Pompano Beach driveway. If it isn’t in writing, it isn’t a warranty.
What ECO Window Systems Custom & Geometric Windows Costs in Pompano Beach
Straight numbers from the work we do in Pompano Beach every month. These ranges cover typical ECO custom and geometric repairs and replacements.
- Resealing a glazing bead or small leak (no glass replacement): $180-$320
- New IGU for a half-round, arch-top, or radius unit (up to 30 x 30 inches): $340-$580
- New IGU for a large trapezoid, parallelogram, or oversized geometric unit: $600-$1,100
- Complete custom-shape window replacement (same opening, new frame and glass): $900-$2,200 depending on size, shape complexity, and glass package
- Hurricane-rated impact custom window replacement: $1,400-$3,400 for most single openings
What moves the price: glass type (clear, low-E, tinted, or impact-rated), whether the shape is a simple radius or a compound curve, frame condition, and access. A second-story half-round over a staircase costs more than a ground-floor circle-top because of ladder work and setup. We give you a written, line-item quote before work starts, and the number on the quote is the number on the bill. Call (863) 591-8673 for a free estimate on your specific window.
Why Pompano Beach Homeowners Call TruePane Windows & Doors for ECO Window Systems Work
We’ve been at this in Pompano Beach long enough to know that a custom window is only as good as the joint between the glass and the frame. Dale Kessler grew up in Pompano Beach Highlands and spent enough summers watching salt air eat through poorly sealed frames to understand exactly what a bad glazing job costs a homeowner over time. That’s the standard our techs work to on every ECO shaped unit, regardless of brand. Every job carries the Done Right Promise, and we register both manufacturer warranty layers in writing before we leave. If your ECO window turns out to be beyond repair, we’ll quote you real alternatives from lines we carry, including PGT, CGI, CWS, and ES Windows, side by side on paper. We answer the phone 24 hours a day, and we’ll be there when we say. If the pane is not true, the job is not done.
FAQs
Yes. We match the frame finish and glass sightline to the existing ECO units in your Pompano Beach home so the new shaped window sits within the same visual plane as its neighbors. We’ll bring actual finish samples before ordering, not a digital color swatch. Call (863) 591-8673 and we’ll take a look at the unit in person.
Yes, when the job requires it. Impact-rated and structural custom window replacements in Pompano Beach need permitting, and we handle that end to end: drawings, submittal, inspection, and closeout. Small repairs like IGU replacement or hardware swap don’t require a permit. We’ll tell you upfront which bucket your job falls in.
No. The quote we hand you is the price you pay. If we open the window and find something we couldn’t see before, we stop, show you, and put the revised number in writing before moving forward. No surprise line items on the bill, no change orders you didn’t sign.
Most IGU replacements and hardware repairs on ECO shaped windows are done in a single visit, typically two to four hours depending on the size and access. Full custom window replacements take longer because of fabrication and, when required, permit inspection. We’ll give you a straight answer on timing when we see the window.
We work to protect any remaining ECO manufacturer warranty on your unit. That means documenting the failure, matching parts and glass to the original spec, and giving you a written record of what was replaced and why. We’re independent, not an ECO authorized dealer, so we’ll tell you plainly if a repair could affect your warranty before we touch anything. If it isn’t in writing, it isn’t a warranty.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Pompano Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.